What is the torque spec for the oil drain plug on a 2007 Honda?

For most 2007 Honda models, the oil drain plug torque target sits in a relatively narrow range, but the exact figure is model- and engine-specific. A practical starting point is about 22–25 ft-lbs (30–34 Nm), but you should verify the precise spec for your exact vehicle configuration.

Why the exact torque matters

The torque you apply to the oil drain plug matters because too little torque can lead to oil leaks, while too much can strip threads or warp the oil pan. Honda designs its drain plugs and gaskets to seal properly at a specific torque, which also helps maintain oil pressure and engine cleanliness over time.

Typical range and model differences

Torque figures for 2007 Honda models vary with engine type and oil pan design. As a general guideline, many 2007 Hondas target a torque in the low 20s to mid-20s ft-lbs, with the corresponding range around 30–34 Nm. Exact values depend on your engine code (for example, R-series, K-series, or J-series engines) and whether a copper washer or o-ring is used. Always confirm the exact specification for your vehicle before finalizing torque.

Where to find the exact spec for your car

The correct figure depends on your car’s model and engine. Use these sources to confirm the torque specification for your 2007 Honda:

• Official Honda service information portals and factory manuals (Honda TechInfo or equivalent dealership resources).


• Authorized repair databases such as Alldata or Mitchell1 that list torque specs by model and engine code.


• Your vehicle identification number (VIN) or engine code to locate the exact spec in the manual or dealer portals.


• Honda dealership service departments or certified mechanics, who can confirm the precise torque for your exact configuration.

Concluding note: Always verify the torque spec for your exact 2007 Honda model and engine. While a practical target is around 22–25 ft-lbs (30–34 Nm), the precise value may differ by engine code and component design. Using the correct torque helps prevent leaks and ensures the oil change seals properly.

How to apply the torque correctly

Tools, preparation, and technique influence how accurately you achieve the correct torque. The following steps help ensure you tighten the drain plug properly and safely.

Tools and safety considerations

Use a clean, correctly sized socket for the drain plug, and a calibrated torque wrench appropriate for the expected range. Inspect and replace the copper washer or gasket as recommended by Honda. Work on a level surface with the engine cool before performing the torque procedure.

• Clean the drain plug and oil pan threads; install a new washer if required by your engine type.


• Thread the plug by hand to avoid cross-threading, then snug it by hand until seated.


• Set your torque wrench to the specified torque for your model and engine, and tighten until you reach that value.


• Wipe away any oil residue and start the engine briefly to check for leaks, then recheck torque after the engine cools if needed.


• Dispose of used oil properly and inspect the drain area for signs of seepage after the next few drives.

Note: Do not exceed the manufacturer’s torque specification. Overtightening can damage threads and the oil pan, leading to costly repairs.

Summary

For a 2007 Honda, the oil drain plug torque is model- and engine-dependent, but a practical starting point is about 22–25 ft-lbs (30–34 Nm). The exact value should be pulled from the owner’s or service manual for your specific model and engine code. Verify the spec with reliable sources such as Honda’s official service information, authorized databases, or a dealership to ensure a proper seal and avoid damage. A correct torque, fresh washer, and leak check contribute to a reliable oil change and engine protection.

What is the torque on a Honda drain plug?

The Honda drain plug torque varies by model, but for many common models, it is around 29 to 30 ft-lb. Always check your specific vehicle's owner's manual or a reliable service manual for the exact specification, as torque values can differ between engine sizes and model years. For example, some Honda Accords use a torque of 29 ft-lb, while some 2014 Honda Accords have a transmission drain plug torque of 36 ft-lb.
 
This video shows the location of the oil drain plug on a Honda CR-V: 41sTechnical EvolutionYouTube · Jun 14, 2025

• Most Common: Approximately 29 to 30 ft-lb for many Honda engine oil drain plugs. 
• Examples:
  • 2007 Honda Odyssey: 29 ft-lb 
  • 2017 Honda Pilot: 29 ft-lb 
  • 2016 Honda Civic 1.5T: 30 ft-lb 
  • 2014 Honda Accord (Transmission): 36 ft-lb 

This video demonstrates the correct torque for a Honda oil drain plug: 48sRepair NutYouTube · May 27, 2024
Important:

• Always use a new crush washer to ensure a proper seal. 
• Do not overtighten, as this can strip the threads in the oil pan. 
• It is highly recommended to use a torque wrench for accuracy and to prevent damage. 

What size is the oil drain plug on a 2007 Honda Civic?

The 2007 Honda Civic oil drain plug has a M14-1.50 thread size and requires a 17mm wrench or socket to remove. It is crucial to replace the crush washer when installing the new plug to ensure a proper seal. 

• Thread Size: M14-1.50
• Head Size: 17mm
• Recommendation: Always replace the crush washer when changing the oil.

How many quarts of oil does a 2007 Honda Accord 2.4 take?

A 2007 Honda Accord 2.4L takes 4.4 quarts of oil when changing the filter. It is crucial to check the oil level after refilling and before driving to ensure the correct amount is in the engine. 

• With filter change: 4.4 quarts
• Without filter change: 4.2 quarts
• Recommended oil: 5W-20

What is the torque spec for the oil drain plug on a 2007 Honda Odyssey?

The 2007 Honda Odyssey oil drain plug should be torqued to 29 ft-lb (39 Nm). Be sure to use a new crush washer each time you change the oil to ensure a proper seal and to avoid stripping the threads in the oil pan.
 
This video demonstrates the process of changing the oil and filters in a Honda Odyssey from 2005 to 2010, including tightening the drain plug: 1mMC FIX ITYouTube · Jun 18, 2024

• Torque: 29 ft-lb (39 Nm) 
• Important: Always replace the crush washer on the drain plug with a new one to prevent leaks. 
• Caution: Do not overtighten the drain plug, as this can damage the threads in the oil pan. 

This video shows the location of the oil drain plug and the entire oil change process for a Honda Odyssey: 57sAuto Repair GuysYouTube · Jun 25, 2017