Where are the jack points on a 2007 Ford Fusion?
The main front lifting point is the reinforced front subframe crossmember, and you can also use the rocker-panel pinch welds for side lifting. For rear work, use the rear pinch welds along the rocker panels. Always support the car with jack stands and work on a flat surface.
Understanding where to jack a 2007 Ford Fusion helps you perform tire changes or brake maintenance safely. The vehicle’s chassis includes a sturdy front crossmember and reinforced pinch welds along both sides of the rocker panels to accommodate a floor jack. Using the correct points prevents damage to the undercarriage and reduces the risk of the vehicle shifting or collapsing while you’re underneath it.
Primary lift points to use with a floor jack
Before listing the lift points, note that the Fusion’s undercarriage includes a sturdy front subframe crossmember suitable for center lifting, as well as reinforced pinch welds along the rocker panels for lateral lifting. The following points are commonly used by owners and technicians when lifting the vehicle with a floor jack.
- Front center jack point: Use the reinforced front subframe crossmember located behind the front bumper. Position the floor jack under this crossmember and raise the vehicle slowly.
- Front pinch welds (left and right): The rocker panels along the doors have reinforced pinch welds designed for side lifting on both sides; place the jack under the pinch weld on the corresponding side.
- Rear pinch welds (left and right): Reinforced pinch welds along the rear doors on the rocker panels; use them to lift the rear of the Fusion if you need to access the underside or rotate the wheels.
When using these points, ensure the jack is fully stable and that the load is distributed evenly across the lift point. If you’re performing a full raise, plan to place jack stands at appropriate support points as soon as the vehicle is high enough to safely accommodate them.
Safety considerations
Always consult the owner's manual for the exact jacking points and the recommended precautions for your vehicle variant. Use a stable, flat surface, place wheel chocks on the opposite wheels, and never place any part of your body under the car while it is supported only by a jack. After lifting, secure the vehicle with jack stands on solid points before performing any work underneath.
Summary
For a 2007 Ford Fusion, the safest jack points are the front center jack point on the front subframe crossmember, plus the pinch welds along the rocker panels on both sides for side lifting (front and rear). Always use jack stands on a flat surface and follow the manual’s guidance to prevent damage or injury.
Where is the jack point on a Ford Fusion?
The jack points on a Ford Fusion are the reinforced metal pinch welds located under the doors, between the front and rear wheels. You can also use the cradle in the front, a solid steel structure near the engine and suspension, or the frame rail at the rear for lifting with a jack or jack stand. Always consult your owner's manual for the specific locations on your model year, as there might be arrows or notches indicating the exact spots.
This video demonstrates how to jack up a Ford Fusion safely: 58sCarParts.comYouTube · May 9, 2025
Front jack points
- Pinch weld: The most common point is on the metal lip that runs along the side of the car, just under the door. Look for arrows on the lower side skirt pointing to the correct spot.
- Cradle: For lifting the entire front, use the solid steel cradle in front of the engine and suspension components.
Rear jack points
- Pinch weld: Similar to the front, use the reinforced pinch weld under the rear door.
- Frame rail: The frame is a secure place for both jack stands and lifts.
Tips for safely jacking up your Fusion
- Park the vehicle on a flat, stable surface.
- Engage the parking brake and place wheel chocks behind the wheels to prevent the car from rolling.
- Loosen the lug nuts slightly before lifting the car.
- Place a jack stand under a sturdy part of the chassis after lifting, but before lowering the jack completely.
- Use a jack pad or a block of wood to protect the pinch weld if using a floor jack, as the metal can bend or break.
This video shows how to safely jack up a Lincoln MKZ/Ford Fusion for a 2013-2020 model: 43s321verykind AUTOSYouTube · Dec 10, 2022
How to jack up a 2007 Ford Focus?
So simply jack the car up as high as you need it using the jack. And then once you've got it as high as you want put the axle stand in position. And then lower it down onto. It.
How do I know where my jack points are?
Jack Points on a Car (Quick Answer)
Most cars have four main spots. Look just behind the front wheels and just in front of the rear wheels along the pinch weld seam. Those areas are beefed up from the factory to take the load.
How to jack up a 2007 Ford Fusion?
Point. Then slowly lower your vehicle until it is stable on the jack. Stand. You can now remove the wheel if needed. For safety slip it under the vehicle as additional protection.
