Where is the oil filter located on a 2010 Acura TL?
As a seasoned auto repair professional, I often get questions about the location of specific car components, such as the oil filter. If you own a 2010 Acura TL and are planning to perform an oil change yourself, knowing where the oil filter is located is essential. In this article, I’ll guide you through its location and provide some tips for accessing it safely and efficiently.
Understanding the Oil Filter's Role
The oil filter is a critical component of your car's engine. It removes contaminants from the engine oil, ensuring that the oil circulating through the engine is clean and effective at lubricating moving parts. Regularly replacing the oil filter during oil changes is vital for maintaining engine health and performance.
Location of the Oil Filter on a 2010 Acura TL
The oil filter on a 2010 Acura TL is located underneath the vehicle, near the front of the engine. Specifically, you’ll find it on the passenger side, close to the oil pan. It is mounted in a vertical position, making it relatively easy to access during an oil change.
Steps to Access the Oil Filter
To safely access and replace the oil filter, follow these steps:
- Step 1: Park your car on a flat surface and engage the parking brake. Ensure the engine is cool before starting.
- Step 2: Use a jack to lift the front of the car and secure it with jack stands for safety.
- Step 3: Locate the oil filter on the passenger side of the engine, near the oil pan.
- Step 4: Place an oil drain pan underneath the filter to catch any oil that may spill during removal.
- Step 5: Use an oil filter wrench to loosen and remove the filter. Be cautious, as it may still contain oil.
Tips for a Smooth Oil Filter Replacement
Here are some additional tips to make the process easier:
- Always wear gloves to protect your hands from oil and debris.
- Inspect the old filter to ensure the rubber gasket is removed along with it. Leaving the gasket behind can cause leaks.
- Apply a thin layer of fresh oil to the gasket of the new filter before installation. This helps create a proper seal.
- Hand-tighten the new filter until it is snug, then give it an additional quarter turn. Avoid over-tightening.
Conclusion
Locating and replacing the oil filter on a 2010 Acura TL is a straightforward process with the right tools and preparation. Regular oil changes, including replacing the oil filter, are essential for keeping your engine running smoothly and efficiently. If you’re ever unsure or need assistance, don’t hesitate to visit a trusted auto repair shop like Kevin’s Autos for professional service.
Frequently Asked Questions
Where can I check my oil filter?
Pan. Use your finger to dab a bit of fresh oil on the new filter's gasket and spread it around evenly. Then twist the filter onto the stud. And tighten by hand until it is snug.
Where is the oil filter housing located?
The oil filter housing on most cars is located in a spot that's easily accessible for oil and filter changes, typically either on the top of the engine near the front or on the side of the engine with the filter accessible from the bottom.
Where in the lubrication system is the oil filter placed?
Return-line filters are common in most hydraulic systems. They are installed in the line after all lubricated components and before the main reservoir.
What are the symptoms of a bad oil filter housing gasket?
A sudden decrease in oil level without an apparent reason could indicate a leak in the engine oil filter housing. Oil leaks also affect engine performance; look out for decreased power, unusual noises, or the engine running roughly.
Where is the fuel filter located on a 2010 Acura TSX?
Where is the fuel filter located on my Acura? The fuel filter is always going to be found between the fuel tank and the engine. For most vehicles, the fuel filter is located inside the top of the fuel tank, right where it connects with the fuel line, although on some cars if might be elsewhere along the fuel line.
How many gallons does a 2010 Acura TL have?
18.5 gal
2010 Acura TL - Specifications
| POWERTRAIN | |
|---|---|
| Engine Type | |
| Fuel Tank | 18.5 gal (70 L) |
| EPA Passenger Volume | 98.2 cu ft; 111.3 cu ft (passenger and cargo volume combined) |
| EPA Cargo Volume | 13.1 cu ft |
Can I change the oil filter myself?
Gasket on the new oil filter. And then screw it onto the engine. By hand tighten the filter. Using a wrench being careful not to overtighten.
Where is the oil filter placed?
In most vehicles, the oil filter is located on the engine block, near the oil pan. However, in others, the oil filter may be in a different location, such as above the engine, behind the radiator, or in the fender well. To find the exact location of your oil filter, you can refer to your car's owner's manual.
How many quarts of oil does a 2010 Acura TL take?
4.5 quarts
What is the best oil for 2010 Acura TL?
If you own a TL between model years 2004-2014, your engine's recommended oil is 5W-20, a fully synthetic oil; if your Acura TL model is even older, from model years 1999-2003, the most versatile and safe oil to use in your engine is 5W-30 synthetic oil.
